Learning the Basics of Installing a Bathtub
Learning the Basics of Installing a Bathtub
Blog Article
They are making a few good pointers regarding Tools You Need to Install a New Bathtub as a whole in this post directly below.
Installing a tub isn't precisely rocket science, yet it does call for strong plumbing, carpentry, as well as occasionally, tiling abilities. Replacing an old bath tub with a brand-new one is likewise a moderately challenging job. If the old bathtub is easily accessible, the job can relocate speedily; if you need to open a wall surface to remove the old tub as well as position the brand-new bath tub, the task is a lot harder. In either situation, the project is within a house handyman's abilities, although you will certainly need a helper to vacate the old tub as well as embeded in the new one. Make sure you have certified yourself for the job as well as fit attempting it. Rather than hiring a service provider to take control of a halfway-completed task, it is far better to think about utilizing one before you start. Chances are you may need a specialist plumber to make tube connections.
This write-up will certainly assist you install a brand-new bath tub in your washroom if you have already bought a new tub and don't need to transform the setup of your previous water pipelines.
Your devices and product checklist should consist of the following:
Removing Old Taps
If you require to change old taps with brand-new ones as a part of your installment, after that the first thing you need to do is detach the water. After doing so, activate the taps to drain pipes any type of water remaining in the system. The procedure of removing the existing faucets can be fairly problematic as a result of the restricted access that is often the situation.
Make use of a basin wrench (crowsfoot spanner) or a tap device to undo the nut that connects the supply pipes to the taps. Have a towel all set for the continuing to be water that will come from the pipes. Once the supply pipes have actually been eliminated, use the same tool to loosen the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary faucets from turning during this procedure. When the faucets have been gotten rid of, the holes in the bath/basin will have to be cleansed of any type of old sealing substance.
Prior to carrying on to fit the new taps, compare the pipe connections on the old faucets to the new faucets. If the old taps are longer than the new taps, after that a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, after that you will certainly need a plastic adapter to prevent damage to the thread. One end of the adapter fits on the plastic tail of the tap as well as the various other end supplies a link to the current supply pipelines.
If you need to fit a monobloc, then you will call for decreasing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipeline.
Next off, position the tap in the installing opening in the bath/basin guaranteeing that the washers remain in location between the faucet and also the sink. Secure the faucet in position with the supplier provided backnut. As soon as the faucet is securely in place, the supply pipes can be attached to the tails of the taps. The taps can either be linked by using corrugated copper piping or with normal tap adapters. The previous kind needs to be connected to the tap finishes first, tightening up only by hand. The supply pipes can later on be connected to the various other end. Tighten both ends with a spanner after both ends have actually been attached.
Setting up the Tub
Utilizing both wood boards under its feet, put the bath tub in the required position. The wood boards are valuable in evenly spreading out the weight of the bath tub over the location of the boards instead of concentrating all the weight onto four little factors.
The following objective is to make sure that the tub is leveled all round. This can be attained by inspecting the level and also readjusting the feet on the tub till the spirit level reviews level.
To set up faucets, fit the bottom of the outermost adaptable faucet adapter to the appropriate supply pipeline by making a compression join; then do the same for the other tap.
Turn on the water system and inspect all joints and also new pipework for leaks and tighten them if needed. Load the bathtub as well as additionally inspect the overflow outlet as well as the regular electrical outlet for leakages.
Ultimately, deal with the bathroom paneling as explained in the supplier's user's manual. Tiling and also securing around the bathtub must wait up until the bathtub has been made use of at least once as this will resolve it into its last placement.
Getting ready for the Installation
First of all, the supporting structure provided with the bathroom ought to be fitted (if needed) according to the producer's directions. Next, fit the faucets or mixer to the bathtub. When suitable the tap block, it is very important to make certain that if the faucet features a plastic washer, it is fitted between the bathroom and the faucets. On a plastic bath, it is likewise practical to fit a sustaining plate under the faucets device to stop stress on the bath tub.
Fit the adaptable faucet adapters to the bottom of both faucets making use of 2 nuts and also olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink outlet opening, and afterwards pass the outlet via the hole in the bathroom. Utilize the nut provided by the maker to fit the plug-hole. Analyze the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the versatile overflow pipe to the overflow electrical outlet. After that, screw the pipeline to the overflow face which should be fitted inside the bath. See to it you use all of the provided washers.
Connect the trap to the bottom of the waste electrical outlet on the bath tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the trap to the electrical outlet. Link all-time low of the overflow tube in a comparable manner.The bath must currently be ready to be suited its final setting.
Tiling Around the Tub
In the area where the bath fulfills the tile, it is essential to secure the accompanies a silicone rubber caulking. This is very important as the installation can relocate sufficient to split a rigid seal, creating the water to penetrate the wall surface in between the bathroom and the tiling, bring about complications with moisture and possible leaks to the ceiling below.
You can select from a selection of coloured sealants to assimilate your fixtures as well as fittings. They are sold in tubes and cartridges, and can sealing spaces as much as a size of 3mm (1/8 inch). If you have a bigger space to load, you can fill it with spins of drenched paper or soft rope. Remember to always load the tub with water prior to securing, to allow for the movement experienced when the bathtub is in usage. The sealer can crack rather very early if you do not think about this activity prior to sealing.
Conversely, ceramic coving or quadrant tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are also easily readily available on the market. It is suggested to fit the ceramic tiles using waterproof or waterproof adhesive and also grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
I stumbled upon that piece on Tools You Need to Install a New Bathtub when perusing the web. Sharing is caring. Helping others is fun. Thank you so much for going through it.
More Details Report this page